RAGE 1200’s  

Relieving the MA’s of their duty, the latest RAGE mulitchannel amplifiers won’t come up short in any way! Newly added features, decreased footprint & greater power are all on the checklist.
Whether it is 1200 watts into 2 or 4 channels, The RAGE 1200’s will keep it under control.

No RCA

No problem, on these amps we have added High Level inputs. Previously you may have gotten around it by using adapters, whereas we offered our active DSP, The RAGE FIEO to connect your OEM system to external amplification. If you only require an upgrade on the front speakers and an external sub, then the RAGE 1200.2 offers RCA out connection.

MINI is greater

Considering the 1200’s has decreased its footprint by min 15%, but increased its power by 20% due to entirely new optimized circuits, it is not only an achievement, but directly beneficial to your install and your pockets.  All it takes is 10.6 x 6.45 x 2.28 ” / 27 x 16.4 x 5.8 cm to house the 1200 watts. But how about rise? Even though the 8 Ω rating isn’t stated, it is about 70% of the 4 Ω rated power. Key features from the MA’s such as the clip indicator has been carried over. So has the ACCU8 crossovers with designated frequencies on the potentiometers, (see the manual for a full frequency list).

HIGH VOLTAGE

With today’s more advanced battery tech and lithium finding its way into car audio, we have tweaked the operation voltage all the way up to 17.5 V. By doing so you don’t need to worry about running your batteries at a low SOC and amplifiers going into protect.

RAGE1200.2 / RAGE1200.4 manual

SPECIFICATIONS	RAGE 1200.2	RAGE 1200.4
Frequency Response:	10 Hz ~ 25 KHz	10 Hz ~ 25 KHz
Signal to Noise Ratio:	>90 dB	>90 dB
Input Sensitivity:	5 V ~ 0.2 V	5 V ~ 0.2 V
Low Pass Crossover 24 db/ Oct:	20 Hz ~ 1 KHz	20 Hz ~ 1 KHz
High Pass Crossover 24 dB / Oct:	40 Hz ~ 5 KHz	40 Hz ~ 5 KHz
Damping Factor:	>400	>400
Power Terminal gauge:	4 GA	4 GA
Fuse Rating:	100 A	100 A
Operational voltage:	9 V ~ 17.5 V	9 V ~ 17.5 V
Dimensions:	10.6" x 6.45" x 2.28" 270 x 164 x 58 MM	10.6" x 6.45" x 2.28" 270 x 164 x 58 MM
Power @ 4 Ω 13.8 V: Power @ 4 Ω 14.4 V:	2 x 350 w 2 x 400 w	4 x 200 w 4 x 250 w
Power @ 2 Ω 13.8 V Power @ 2 Ω 14.4 V:	2 x 550 w 2 x 600 w	4 x 275 w 4 x 300 w
Power @ 4 Ω bridge 13.8 V: Power @ 4 Ω bridge 14.4 V:	1 x 1100 w 1 x 1200 w	2 x 550 w 2 x 600 w

*In order to get the full power output of the amplifier, it is crucial that your electical system is correctly (over) dimensioned. Failure to upgrading will constrain the power output & lower the efficiency.  This can cause damage to the amplifier &  void the warranty. Drivng the amplifier with  ohm loads below of what is written in the manual is another void.  Therefore take your time and read the manual thoroughly prior to installing! **Marine capable products are not to be subjected directly to water, but has the ability of being functional in humid conditions.